Setup a Management Port on your Dell PowerConnect 6200 series switch. If you are using the Dell PowerConnect 6224 or 6248 switches, this can easily be created at the console prompt. Before you begin, you need to choose a vlan ID, an IP address that the switch can be managed on, and a switch port that will be connected to the. Installation: Dell PowerConnect 5224 Systems User's Guide Dell PowerConnect 5224 Systems User's Guide Before you begin installing the switch, confirm that your package contains the following items: • Switch • AC power cable • Null modem cable • Self-adhesive rubber pads for desktop installation • Rack mount kit for rack installation • Documentation CD NOTICE: Do not connect the switch to the network until you have established the correct Internet Protocol (IP) settings. Before you connect to the network, you must install the switch on a flat surface or in a rack, set up a terminal emulation program, plug in the power cord, and then set up a password and IP address. The switch is supplied with rubber feet for stationing it on a flat surface and mounting brackets and screws for mounting the switch in a rack. Install the switch on a level surface that can safely support the weight of the switch and its attached cables. The switch must have adequate space for ventilation and for accessing cable connectors. • Set the switch on a flat surface and check for proper ventilation. Allow at least 2 inches (5.1 centimeters [cm]) on each side of the switch and 5 inches (12.7 cm) at the back for the power cable. • Attach the rubber feet on the marked locations on the bottom of the chassis. The rubber feet, although optional, are recommended to keep the unit from slipping. You can install the switch in most standard 19-inch (48.3-cm) racks. NOTE: For racks that are not prethreaded, cage nuts are provided. • Use the supplied screws to attach a mounting bracket to each side of the switch. • Align the holes in the mounting bracket with the holes in the rack. • Insert and tighten two screws through each of the mounting brackets. Presenting to you the exclusive trailer of Home Sweet Home 1. Watch the full movie exclusively on Goencho Balcao. Latest Konkani Movies Online on www.goenchobalcao. Home Sweet Home 2. The makers of Konkani movie “Home Sweet Home” have announced a sequel to the film, which will start its shoot in December this year. Advertising The movie, which was released last year, is still running in various theatres across the state. “Home Sweet Home” makes a statement on the current. Home sweet home is highly entertaining loaded with witty and humorous dialogues. The story is one that every goan can relate to. The way john d'silva behaves when he finds his home replaced is exactly the way a common man would had behaved.There is no dull situation and there is equal blend of comedy and emotions. Home sweet home konkani movies nosha. The switch supports the Dell PowerConnect RPS-600 external redundant power system. NOTE: See the RPS-600 documentation for more information. CAUTION: Do not use the switch with any redundant power system other than the Dell PowerConnect RPS-600. The switch provides an RS-232 serial port that enables a connection to a computer or terminal for monitoring and configuring the switch. This port is a male DB-9 connector, implemented as a data terminal equipment (DTE) connection. To use the console port, you need the following equipment: • A terminal or a computer with both a serial port and the ability to emulate a terminal • A null modem or crossover RS-232 cable with a female DB-9 connector for the console port on the switch To connect a terminal to the console port: • Connect the female connector of the RS-232 cable directly to the console port on the switch, and tighten the captive retaining screws. • Connect the other end of the cable to a terminal or to the serial connector of a computer running terminal emulation software. ![]() Set the terminal emulation software as follows: • Select the appropriate serial port (COM port 1 or COM port 2). File complaint us postal inspector pay. • Set the data rate to 9600 baud. • Set the data format to 8 data bits, 1 stop bit, and no parity. • Set flow control to none. • Under Properties, select VT100 for Emulation mode. • Select Terminal keys for Function, Arrow, and Ctrl keys. Ensure that you select Terminal keys ( not Windows keys). NOTICE: When you use HyperTerminal with the Microsoft® Windows® 2000 operating system, ensure that you have Windows 2000 Service Pack 2 or later installed. Windows 2000 Service Pack 2 allows you to use arrow keys in HyperTerminal's VT100 emulation. See www.microsoft.com for information on Windows 2000 service packs. • After you have correctly set up the terminal, plug the power cable into the power receptacle on the back of the switch. The boot sequence appears in the terminal. • After the boot sequence completes, the console login screen displays.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |